View MSM9026_399033.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOSEL VITELIC
October 1996 Features
To emulate S1207 chip and its derivatives, see data sheet PID 247. Driven by either 1.5 V x 4 battery or 5 - 6 V power supply. A 4x1 jumper header JP1 is provided to accept power source. A pair or strengthen wire (E1 & E2) is provided to accept the power source. 2 push button switches are provided to control the power on/off. Selectable (by JP2) auto power off function (after 60" no operation)is provided. A push button switch is provided to reset this M9026 board.
MSM9026
Emulation Board for S1207
A red LED lamp D3 is provided to indicate the power on or off. A 32-pin textool U3 is provided to store 27C010 EPROM (access time 120 ns or faster). 5 green LED lamps are provided on EAC area. 5 red LED lamps are provided on EAC area. 19 push button switches for triggers are provided on EAC area. A 2x1 jumper header JP4 is provided on EAC area to accept wires to speaker. A 3x1 jumper header JP5 is provided on EAC area to decide source for K1,2,3,4 triggers. A 3x5 jumper header is provided on EAC area to select LED lamps for 5 output pins or not. To be continued on page 3/6.
Description
By storing digitized sound data and options into 27C010 and inserting it onto U3, this MSM9026 board emulates the function of S1207 chip and its derivatives. The file for 27C010 content should be prepared by running program 9026pack.exe. The demanded external components are provided on board in specific EAC (External Application Component) area.
Board Layout
MOSEL VITELIC INC., MSM9026 V1M1 1996
E1 Vcc
U3
U2
(80C31) 9026 F/W 1.00
TEXTOOL for 27010
1.5V x4 JP1 E2 GND
(Red) OS DRV JP4
OW
OX
OY
OZ
Vdd TGA TGB TGC OS OW OX OY OZ
SW JP3
Vss K1 K2 K3 K4 RW1 RW2 RW3 RW4 Cout
JP2 Auto Power Off RST
SPK SNK (Green) OS SN: OW OX OY OZ
SW4
SW8
SW12
SW16 RW4
SW3
SW7
SW11
SW15 RW3 HI A B C Vdd SEL RW2 LO A B C OKY RW1 JP5
SW2
SW6
SW10
SW14
RW1 INT SW SW
SW1
SW5
SW9
SW13
K1
K2
K3
K4
TGA
TGB
TGC ON/OFF D3
1/6
PID342 10/96
MOSEL VITELIC
MSM9026
Block Diagram & Schematics
OS
OW
OX
OY
OZ Green SNK
OZ OY OX OW OS
RST
1
1
1
1
1
ON OFF S1207 Equivalent Circuit Power Control Circuit
OS
OW
OX
OY
DRV OZ Red
JP2
R31 A HI LO R38 A
R32 B
R33 C
INT TGC
TGB R39 B R40 C OKY
TGA
SPK
32
Q3 8050
JP4
One 16X2 EPROM Textool
RW4 RW3 RW2 RW1 JP5
SW16 SW15 SW14 SW13
K4 K3 K2 K1
SW12
SW11
SW10
SW9
SW8
SW7
SW6
SW5
SW4
SW3
SW2
SW1
2/6
PID342 10/96
MOSEL VITELIC
MSM9026
Features
(continued)
A 3x6 jumper header is provided on EAC area to select drive circuit for 3 trigger inputs. A transistor 8050 is provided on EAC area to drive the current running through speaker. The board's AC characteristics is not identical to chip's.
The board's DC characteristics is not identical to chip's. The board's behavior is not identical to chip's. Neither identical to S1207's derivatives.
DC Characteristics
Symbol V iL V ih V oL V oh I iL I ih I oL I oh I co I co Parameter input low V input high V output low V output high V input low I input high I output high I output high I Current output Current output Valid TGA,B,C TGA,B,C OS,W,X,Y,Z OS,W,X,Y,Z TGA,B,C TGA,B,C OS,W,X,Y,Z OS,W,X,Y,Z Cout Cout Min 3.15 Vcc-0.1 -1 1 4 -4 2.2 2.8 Typ. Max. Unit 0.9 V V 0.1 V V uA uA mA mA mA mA Remark
V0=0.4V V0=Vcc-0.8 5 Vdd 6 Vdd
The DC characteristics of TGs input and outputs are the same as those of 74Cxx series.
AC Characteristics
Symbol t STP tT tT tT tT tT tT tT tT f f f f f f f f Parameter Stop pulse width Trigger pulse width Trigger pulse width Trigger pulse width Trigger pulse width Trigger pulse width Trigger pulse width Trigger pulse width Trigger pulse width Valid OS,W,X,Y,Z TGA,B,C TGA,B,C TGA,B,C TGA,B,C TGA,B,C TGA,B,C TGA,B,C TGA,B,C LED LED LED LED LED LED LED LED Min Typ. 30 10 13 15 17 20 23 25 27 198% 158% 133% 115% 100% 88% 80% 73% Max. Unit ms ms ms ms ms ms ms ms ms f led f led f led f led f led f led f led f led Remark pitch independent pitch = 0, SRI pitch = 1, SRI pitch = 2, SRI pitch = 3, SRI pitch = 4, SRI pitch = 5, SRI pitch = 6, SRI pitch = 7, SRI pitch = 0, SRI pitch = 1, SRI pitch = 2, SRI pitch = 3, SRI pitch = 4, SRI pitch = 5, SRI pitch = 6, SRI pitch = 7, SRI
SRI := Sample Rate Independent.
3/6
PID342 10/96
MOSEL VITELIC
MSM9026
LED selection by 3X5 Jumper
Red LED.S is used for output OS Green LED.S is used for output OS
1
DRV
DRV
1
SNK
OS
6
SNK
OS
DRV
2
SNK
Red LED.W is used for output OW
DRV
OW
7
SNK 1
Green LED.W is used for output OW
OW
DRV
3
SNK
Red LED.X is used for output OX
DRV
OX
8
SNK 1
Green LED.X is used for output OX
OX
DRV
4
SNK
Red LED.Y is used for output OY
DRV
OY
9
SNK 1
Green LED.Y is used for output OY
OY
DRV
5
SNK
Red LED.Z is used for output OZ
DRV
OZ
10
SNK 1
Green LED.Z is used for output OZ
OZ
Auto Power off control
JP2 open JP2 connected Power always on Auto power off
4/6
PID342 10/96
MOSEL VITELIC
MSM9026
Trigger Drive Selection by 3X6 Jumper
AB HI R S LO R S AB C
R31
Use Vdd to drive TGA through 10K ohm (R31) and SW-TGA
C
TGA
AB HI R S LO R S AB
C
Use Vss to drive TGA through 10K ohm (R38) and SW-TGA
C
R38
TGA
1
AB HI R S LO R S AB C
Use Vdd to drive TGA through SW-TGA
C
TGA
AB HI R S LO R S AB
C
TGA
Use Vss to drive TGA through SW-TGA
C
A HI
BC RS
2
LO RS ABC
Similar operation as TGA's
A HI
B
C RS
3
LO A RS BC
Similar operation as TGA's
5/6
PID342 10/96
MOSEL VITELIC
Before Operating 9026
To prepare voice file(s) To prepare up to 32 voice files by MES 2.0 or 3.0. These files must be 8-bit PCM file. To prepare a filled PRF To write down your demand options on PRF (product request form) is strongly recommended before you are running 9026pack.exe. To prepare a source text Using commercial text editor on personal computer, you can set up a source text in the format defined in 9026pack software user's manual (pid 392 10/96). In this source text, you can define the both word sections and sentence tables. This source text must have the file extension .SRC. Most of mask options can be defined on the screen in 9026pack.exe. The entry dependent options could be defined inside source text. To have a compiled binary file Running 9026pack.exe and entering keystrokes as prompt, you can easily define the options and read in the source text. Completing as the screen tells, you can get a compiled binary file in your specified file name. Its file extension is always .BIN. To have 27C010 programmed Programming this .BIN file into an 27C010 chip by commercial EPROM programmer, you have it ready. To insert this 27C010 To insert this EPROM chip into textool U3 of 9026 board in right direction. To set up LED selections To set up LED connection by jumper 3x5 if needed. To set up Trigger Drive To set up trigger drive circuit as your requirement on jumper 3x6. Without the drive source (either high or low, either R or bare wire) the switch keeps floating and never be capable to activate the trigger. Without right polarity of drive source you can neither trigger the sound and you may hurt this 9026 board.
Taiwan #1, Creation Road I, Science - based Industrial Park, Hsinchu, 30077 Taiwan, ROC "audio_reply@ccmail.mosel.com.tw" TEL: 886-3-5770055 FAX: 886-3-5772788 FAX: 886-3-5784732 Taipei 7F, #102 Sec. 3, Ming Chung E. Road, Taipei,105 Taiwan, ROC TEL: 886-2-5451213 FAX: 886-2-5451214
MSM9026
To configure demanded wires Ensuring you have both 1.5Vx4 power and speaker well connected, this board are ready to work. There are push-button switches to turn on or off the power. Red LED lamp D3 tells the power on. JP2 enables the auto power off function.
Operation Flow
filled Product Request Form Source Text .SRC Voice files
Run 9026PACK.EXE Get Output file filename.BIN and file filename.OPT Go EPROM programmer Get 27C010 programmed Insert onto 9026 board
Warning
Output pin definition restricted: If you select LED dynamic flash, then the M9026 output level will remain the same as the output level of the previous entry. Trigger pin definition restricted: M9026 performs two trigger options only, active high & pull low & low latch as well as active low & pull high & high latch. The M9026 debounce time (min. trigger pulse width) is shown as table in page 3/6, not optional as chip.
Misc
Fuse : Not Available Power : 1.5V x 4 (battery) or 6 VDC power supply Dimension : (LxWxH) 160x115x20 mm textool included Weight : 150 g Demonstration Kit
Hongkong #19 Dai Fu Street, Taipo Industrial Estate, Taipo, N.T. Hongkong TEL: 852-2388-8277(MKO) TEL: 852-2665-4883 FAX: 852-2664-2406 FAX: 852-2770-8011(MKO)
U.S.A. #3910 North First Street, San Jose, CA. 65134-1501 U.S.A. TEL: 1-408-433-6000 FAX: 1-408-433-0952
6/6
PID342 10/96

▲Up To Search▲

Price & Availability of MSM9026

	To Download MSM9026 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .